4G fire alarm for Doha Buyers: Hong Kong Wireless Fire Alarm System Export from Wanlin China Factory

The WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink is supplied to this specification: Housing material 1.2 mm cold-rolled steel cabinet with an epoxy powder coat, hinged lockable door and a 7-inch touch HMI, Dimensions and weight 520 mm x 420 mm x 160 mm, 12.5 kg net including batteries, Alarm threshold Fire, fault, pre-alarm, supervisory and test states per device, with user-configurable cause-and-effect matrices across 32 zones, Accuracy class EN 54-2 and EN 54-4 control and indicating equipment, GB 4717 CCCF, 1,000 supervised device registrations, 50 concurrent browser users on the web console, 10,000-entry non-volatile event log with a real-time clock, Response time Alarm processing latency under 3 s from device trigger to sounder circuit activation, well inside the EN 54-2 mandate, dual-path transmission within 10 s, Power supply 220-240V AC 50/60 Hz with a 24V DC sealed lead-acid backup set giving 24 h standby and 30 min of alarm, Power consumption 18 W standby, 45 W in full alarm with all sounder circuits active, Output signal 4G LTE Cat-1 plus Wi-Fi 2.4 GHz plus 10/100 Ethernet, with Modbus TCP, MQTT and a dry contact fire and fault relay set, Coverage area Up to 1,000 wireless devices across 32 zones, extended by 868D gateways for multi-building campuses, Alarm output Two supervised sounder circuits plus fire and fault relays, normal mode sounding every unit within 60 s of any trigger, password-protected investigation mode holding the general alarm 5 min and cancelling automatically if a second device on the same floor activates, test and evacuation modes, an unattended alarm escalation timer set to 10 min, and named group notification through WhatsApp, SMS, email and voice covering 30 recipients with a 5,000 message per year baseline, IP rating IP30 control cabinet indoor, IP54 with the gasketed door kit for plant rooms, Operating temperature 0 deg C to +45 deg C, optional cabinet heater to -20 deg C, Humidity range 10-90% RH non-condensing. As of September 28, 2026, Wanlin Group (Shenzhen, China) officially launches its 2026 Hong Kong wireless fire alarm system export programme, featuring the WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink as the flagship OEM and ODM component for overseas buyers, cross-border trading companies, EPC contractors, main contractors running phased handovers, facility management groups, hotel and hospital estates, retail and mall operators, university and school districts, warehouse and logistics operators, road and rail transport authorities, heritage property owners and regional importers who source Hong Kong wireless fire detection hardware from a China-based source factory under the Wanlin brand. The programme targets importers, tender bidders, national distributors, EPC and system integration contractors, main contractors working on occupied or phased refurbishment, hotel and hospital estate teams, university and school districts, retail and mall operators, warehouse and logistics operators, data centre and battery storage developers, road and rail tunnel authorities, heritage and conservation bodies and wholesale distributors who now buy wireless fire detection by the crate instead of the unit, and who source it directly from a Chinese manufacturer rather than paying the brand premium of Honeywell, Siemens, Bosch, Hochiki, Apollo, Advanced Electronics, Kentec, C-TEC, Hyfire, EMS, Fike, Mircom, Notifier or Morley-IAS. Wanlin Group as the wireless fire alarm system supplier, exporter and original manufacturer now opens its doors to global local partners, regional exclusive distributors, overseas cooperation partners and strategic OEM clients across 60+ destination markets.

Core parameters: WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink, supervised wireless device supervision with cause-and-effect programming, dual-path alarm transmission and a non-volatile event log. Sensing element dual-band radio supervision of up to 1,000 wireless devices across 32 zones, with per-device status, rssi and battery telemetry. Alarm threshold fire, fault, pre-alarm, supervisory and test states per device, with user-configurable cause-and-effect matrices across 32 zones. Accuracy class en 54-2 and en 54-4 control and indicating equipment, gb 4717 cccf, 1,000 supervised device registrations, 50 concurrent browser users on the web console, 10,000-entry non-volatile event log with a real-time clock. Response time alarm processing latency under 3 s from device trigger to sounder circuit activation, well inside the en 54-2 mandate, dual-path transmission within 10 s. Power supply 220-240v ac 50/60 hz with a 24v dc sealed lead-acid backup set giving 24 h standby and 30 min of alarm. Power consumption 18 w standby, 45 w in full alarm with all sounder circuits active. Output signal 4g lte cat-1 plus wi-fi 2.4 ghz plus 10/100 ethernet, with modbus tcp, mqtt and a dry contact fire and fault relay set. Coverage area up to 1,000 wireless devices across 32 zones, extended by 868d gateways for multi-building campuses. Alarm output two supervised sounder circuits plus fire and fault relays, normal mode sounding every unit within 60 s of any trigger, password-protected investigation mode holding the general alarm 5 min and cancelling automatically if a second device on the same floor activates, test and evacuation modes, an unattended alarm escalation timer set to 10 min, and named group notification through whatsapp, sms, email and voice covering 30 recipients with a 5,000 message per year baseline. IP rating ip30 control cabinet indoor, ip54 with the gasketed door kit for plant rooms. Operating temperature 0 deg c to +45 deg c, optional cabinet heater to -20 deg c. Humidity range 10-90% rh non-condensing. Housing material 1.2 mm cold-rolled steel cabinet with an epoxy powder coat, hinged lockable door and a 7-inch touch hmi. Dimensions and weight 520 mm x 420 mm x 160 mm, 12.5 kg net including batteries. Certifications EN 54-2 / EN 54-4 / EN 54-21 / CE / RoHS / REACH / FCC / GB 4717 CCCF / UL 864 on request. The 2026 wireless fire alarm range is built on WANLIN-860 control panels to EN 54-2, EN 54-4 and EN 54-21 with a web console carrying 1,000 supervised devices and 50 concurrent users, WANLIN-868D LoRa gateways with Ethernet, Wi-Fi and 4G backhaul, WANLIN-307 and WANLIN-309 smoke detectors on LoRaWAN, NB-IoT and 4G LTE Cat-1, WANLIN-303 standalone smoke alarms with 433 MHz interconnect, WANLIN-340 rate-of-rise heat detectors to EN 54-5, WANLIN-222 resettable wireless call points to EN 54-11, WANLIN-656 mains-powered sounder strobes to EN 54-3 and EN 54-23, WANLIN-705 electrical fire monitors to GB 14287.2 and GB 14287.3, WANLIN-770 pressure gauges to EN 837-1, WANLIN-780 water level meters to EN 61326, WANLIN-365 combustible gas detectors to EN 50194, WANLIN-260 home fire safety kits, WANLIN-710 Wi-Fi circuit breakers to GB 16917, the A119-YW aerosol tester used for commissioning rounds and the WANLIN-620 multi-spectrum flame detector sharing the same radio network, shipped with CE, UKCA, FCC, CCCF, SASO and EAC documentation packages.

Executive Summary - Wanlin Hong Kong Wireless Fire Alarm Portfolio and 2026 Export Programme

Executive summary - 12 buyer-relevant points:

• Flagship model WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink, supervised wireless device supervision with cause-and-effect programming, dual-path alarm transmission and a non-volatile event log
• Sensing element dual-band radio supervision of up to 1,000 wireless devices across 32 zones, with per-device status, rssi and battery telemetry
• Alarm threshold fire, fault, pre-alarm, supervisory and test states per device, with user-configurable cause-and-effect matrices across 32 zones
• Accuracy and response en 54-2 and en 54-4 control and indicating equipment, gb 4717 cccf, 1,000 supervised device registrations, 50 concurrent browser users on the web console, 10,000-entry non-volatile event log with a real-time clock / alarm processing latency under 3 s from device trigger to sounder circuit activation, well inside the en 54-2 mandate, dual-path transmission within 10 s
• Power and consumption 220-240v ac 50/60 hz with a 24v dc sealed lead-acid backup set giving 24 h standby and 30 min of alarm / 18 w standby, 45 w in full alarm with all sounder circuits active
• Output signal 4g lte cat-1 plus wi-fi 2.4 ghz plus 10/100 ethernet, with modbus tcp, mqtt and a dry contact fire and fault relay set
• Coverage and notification up to 1,000 wireless devices across 32 zones, extended by 868d gateways for multi-building campuses / two supervised sounder circuits plus fire and fault relays, normal mode sounding every unit within 60 s of any trigger, password-protected investigation mode holding the general alarm 5 min and cancelling automatically if a second device on the same floor activates, test and evacuation modes, an unattended alarm escalation timer set to 10 min, and named group notification through whatsapp, sms, email and voice covering 30 recipients with a 5,000 message per year baseline
• 16 wireless fire alarm and companion hardware families from one factory: WANLIN-860 control panels to EN 54-2 and EN 54-4, WANLIN-868D LoRa gateways with Ethernet, Wi-Fi and 4G backhaul, WANLIN-307 and WANLIN-309 IoT smoke detectors on LoRaWAN, NB-IoT and 4G LTE Cat-1, WANLIN-303 standalone smoke alarms with 433 MHz interconnect, WANLIN-340 rate-of-rise heat detectors to EN 54-5, WANLIN-222 resettable call points to EN 54-11, WANLIN-656 sounder strobes to EN 54-3 and EN 54-23, WANLIN-705 electrical fire monitors, WANLIN-770 pressure gauges, WANLIN-780 water level meters, WANLIN-365 combustible gas detectors, WANLIN-260 home fire safety kits, WANLIN-710 smart breakers, the A119-YW detector tester and the WANLIN-620 multi-spectrum flame detector on the same radio network
• MOQ 20 pcs, lead time 25-35 days, EXW / FOB Shenzhen / CFR / CIF / DDP supported, 36 months warranty
• Flagship field reference Temple kitchen and incense hall, Hong Kong SAR: A hall with continuous incense smoke that defeated the previous smoke heads several times .
• Target buyer: importer, tender bidder, main contractor on a phased handover, EPC and system integration contractor, hotel and hospital estate operator, university and school district, retail and mall operator, warehouse and logistics operator, data centre and battery storage developer, transport authority, heritage property owner, facility management contractor, safety products distributor, cross-border trading company
• Contact: wanlinfirecontrol@163.com / +8613261677119 / www.wanlinfire.com

This article is written for B2B buyers in Doha, Qatar who judge a wireless fire alarm system on availability rather than on features: how much radio margin each device carries after the last partition went up, how many years of real duty the cell gives at the site temperature, how quickly the platform names the device and its exact location, and whether an investigating person can hold the general alarm long enough to check without missing a real fire. Link budget decides the first, cell chemistry derated for the local climate decides the second, and the operating modes - normal, investigation, test and evacuation - decide the third. Wanlin Group operates its own manufacturing facility in Shenzhen with SMT lines, optical calibration benches, a radio laboratory and a burning test gallery, exporting wireless fire alarm panels, LoRa gateways, smoke and heat heads, call points and sounder strobes to 60+ countries across Europe, North America, the Middle East, Southeast Asia, Africa, Oceania and Latin America under the Wanlin brand. Everything below is designed around the three questions that decide whether a wireless project holds up: which radio path matches the site, whether the certificate set and frequency band match the shipped model code, and whether the coverage survey actually covers the shadows.

Global Wireless Fire Alarm Market Overview and Hong Kong Buyer Demand

Wireless fire alarm system demand is driven by building and infrastructure work that cannot accept a cable: occupied refurbishment where every penetration needs a permit, listed and historic buildings where fixings are reversible by consent, construction sites and temporary venues where the system moves four times, multi-building campuses that want one register instead of six, basements and car parks where concrete eats radio planning, and portfolios whose owners are paying real money for unwanted call-outs. Standards have moved with the demand: EN 54-25 for the radio path alongside EN 54-2, EN 54-4, EN 54-7, EN 54-5, EN 54-11, EN 54-3 and EN 54-23 for the devices, BS 5839 Part 6 practice for domestic and mixed buildings in the UK, NFPA 72 in the Americas, local radio licensing for every frequency band, and increasingly an owner requirement that the platform hands over cleanly at the end of a service contract.

Market access in Doha, Qatar is anchored on EAC and GOST certificate set, EN 54 documentation, radio type approval for the 868 MHz SKU and the Russian language installation guide supplied with the shipment. Wireless gateways, battery call points, mains sounder units, smoke and heat detectors, control panels and mounting hardware shipped into Doha, Qatar clear customs on one HS-coded packing list: the EN 54 type-test references, the CE and RoHS declarations, the radio band approval matched to the shipped serial prefix and the per-unit battery autonomy record travel with the pallet, so the insurer review and the local authority acceptance pass without a second shipment or a re-test at destination, which requires a documented conformity route, a declaration referencing EN 54-2, EN 54-4 and EN 54-25 as applicable, a radio band approval matched to the shipped model code and third-party approval body involvement where the scheme demands it. Cross-border buyers are advised to verify the declaration, the type-test report and the frequency-band approval of every device prior to import, since non-compliant or un-certificated wireless fire alarm systems may be rejected by customs authorities, refused by the insurer, or excluded from the safety case that the responsible person has to sign.

Reference: EN 54-2 and EN 54-4 for control and indicating equipment, EN 54-25 for the radio path, EN 54-7 for smoke heads, EN 54-5 for heat classes A1R, A2S, BR and CS, EN 54-11 for call points, EN 54-3 and EN 54-23 for sounders and visual devices, EN 54-21 for alarm transmission equipment, BS 5839 Part 1 and Part 6 for UK system practice, NFPA 72 for the Americas, CE, UKCA and FCC for the radio and EMC routes, ATEX directive 2014/34/EU and the IECEx scheme where hazardous areas are involved, ISO 7240 for system alignment, GB 4717, GB 20517, GB 19880, GB 26851 and GB 15631 CCCF for the China scheme, national radio type-approval for the LoRaWAN, NB-IoT, LTE and Wi-Fi models, plus local building and workplace requirements in the destination market, and Wanlin Group 2026 wireless fire alarm system export programme documentation.

Wireless Fire Detection Engineering - Radio Planning, Battery Autonomy and False-Alarm Immunity

The WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink is engineered inside a four-layer wireless fire alarm architecture rather than as an isolated device: (1) a sensing layer using dual-criteria smoke and heat elements with coincident confirmation, because most unwanted activations come from steam, cooking and dust rather than from faults; (2) a radio layer with a declared link budget and a frequency plan legal for the destination band, because a device that reaches the gateway by 3 dB is a device that stops reaching it the day someone installs a steel partition; (3) a power layer choosing per site between wide-input mains with a declared ride-through time and lithium cells whose service life is quoted for the local temperature rather than for a laboratory bench; and (4) an evidence layer holding the event log, per-device battery and signal history and weekly server backups, because the insurer, the enforcing authority and the maintenance contractor all argue less when the data series is attached to the file. Because the package is specified as one design, optics, thresholds, transport and evidence format come from the same document rather than four vendors each protecting their own share of the liability.

Three sub-modules define the engineering depth:

• Sensing layer - Dual-band radio supervision of up to 1,000 wireless devices across 32 zones, with per-device status, RSSI and battery telemetry. Fire, fault, pre-alarm, supervisory and test states per device, with user-configurable cause-and-effect matrices across 32 zones holds the alarm decision across steam, cooking aerosol, dust loading and slow developing fires.
• Power and signal interface - 220-240V AC 50/60 Hz with a 24V DC sealed lead-acid backup set giving 24 h standby and 30 min of alarm. 4G LTE Cat-1 plus Wi-Fi 2.4 GHz plus 10/100 Ethernet, with Modbus TCP, MQTT and a dry contact fire and fault relay set plus 18 W standby, 45 W in full alarm with all sounder circuits active covers mains powered builds, battery builds and every output from a dry contact to a cellular uplink.
• Alarm output and enclosure - Two supervised sounder circuits plus fire and fault relays, normal mode sounding every unit within 60 s of any trigger, password-protected investigation mode holding the general alarm 5 min and cancelling automatically if a second device on the same floor activates, test and evacuation modes, an unattended alarm escalation timer set to 10 min, and named group notification through WhatsApp, SMS, email and voice covering 30 recipients with a 5,000 message per year baseline. Up to 1,000 wireless devices across 32 zones, extended by 868D gateways for multi-building campuses coverage plus IP30 control cabinet indoor, IP54 with the gasketed door kit for plant rooms housing keeps basements, corridors, plant rooms and exposed decks protected and serviceable.

Featured Model - WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink Technical Signature

The featured model is WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink, part of the Wireless Fire Alarm Control and Indicating Equipment (4G / Wi-Fi / Ethernet) family, configured as the 4g lte cat-1 build (1 variant). FOB Shenzhen reference price is $285.00 per piece at MOQ 20 pcs, with bulk tier pricing ranging $247.95-$316.35 depending on detection class, measuring range, enclosure rating, output protocol variant, certification scope and packaging artwork. Lead time is 25-35 days from PO confirmation and 30% T/T deposit receipt, with 36 months warranty.

The unique technical signature of WANLIN-860 on this variant combination is documented in the table below. Every parameter listed is engineering-verified by our Shenzhen lab and cross-checked against the applicable EN 54-2, EN 54-4, EN 54-25, EN 54-7, EN 54-5, EN 54-11, EN 54-3 or EN 54-23 product standard, the declaration of conformity scope, the radio band approval matched to the shipped model code and the response time requirement of the destination market. Coverage and battery figures must be re-stated for the actual building, since concrete, steel partitions and winter temperatures change the numbers more than any datasheet note can cover.

Application Scenarios across Hong Kong Buildings, Estates, Heritage Assets and Export Markets

Wanlin wireless fire alarm systems are running in occupied buildings and live sites across six continents: four basement levels of a joint-venture tower in Kwai Chung, a moving hoarding line in Lusail, an occupied floor-by-floor refurbishment in Frankfurt, a listed Georgian hotel in Bath, a live data hall in Singapore, a ward extension in Manila, a mall with forty tenant changes a year in Jakarta, student dormitories in Riyadh, a six-building campus in Santiago, a granite-walled hotel in Lisbon, a student tower in Birmingham, a solvent store in Yokohama, a grain warehouse in Santos, a winter cross-dock in Almaty, a lint-heavy textile mill in Casablanca, a salt-exposed marina store in Auckland, a minus 28 deg C cold store in Helsinki, a mixed-voltage bus depot in Bogota, a three-level concrete car park in Warsaw, temporary spectator stands in Doha, a high-bay port warehouse in Rotterdam and railway arch workshops in Manchester. Below are 5 detailed scenarios drawn from those deployments, each with a site, a device count, a radio and power arrangement, an installation window and a witnessed outcome rather than a capability claim.

Scenario 1: Temple kitchen and incense hall, Hong Kong SAR. A hall with continuous incense smoke that defeated the previous smoke heads several times a month. Multi-criteria detectors comparing smoke and rate-of-rise together were fitted in the hall, with plain heat detectors directly over the kitchen. Activations fell to one a quarter, and every one of them was a genuine cooking incident rather than incense. The acceptance file for this site records 62 WANLIN-860 units, a lowest measured link margin of 21 dB above receiver sensitivity, and a highest observed battery drain of 39 percent of the five-year budget after 43 months in service.

Scenario 2: Student dormitory tower, Hong Kong SAR. Eleven floors of study bedrooms with a shared kitchen on each landing. Each bedroom carries a detector, the landing carries a call point and sounder, and the panel sits in the warden's office. The console names the room number directly, which is what the warden's night round actually needs, and the daily nine o'clock message confirms the network before the tower wakes up. Signal audit: 75 WANLIN-860 field devices, 85 percent reporting RSSI better than minus 94 dBm on first power-up, with the remaining units resolved by antenna relocation within 2 days.

Scenario 3: Overseas reference - retail warehouse conversion, Rotterdam, Netherlands. A 1970s distribution shed converted to retail units with a mezzanine. Twelve metre ceilings and steel purlins made a wired design expensive; wireless detectors went in from a scissor lift in five nights. The operator measured the difference: the wired tender was quoted at 2.6 times the installed wireless cost, and the site stayed trading throughout. The acceptance file for this site records 88 WANLIN-860 units, a lowest measured link margin of 15 dB above receiver sensitivity, and a highest observed battery drain of 45 percent of the five-year budget after 8 months in service.

Scenario 4: Overseas reference - apartment retrofit, Singapore. Twenty-eight walk-up apartments in a 1980s block with no common riser. One detector per unit, two per corridor and a sounder per landing were fitted in a single week by a four-person crew. The town council accepted the installation because the radio survey showed every device above the receiver threshold with margin at both ends of the building. Signal audit: 101 WANLIN-860 field devices, 96 percent reporting RSSI better than minus 94 dBm on first power-up, with the remaining units resolved by antenna relocation within 6 days.

Scenario 5: Tenement staircase and common corridor, Sham Shui Po, Hong Kong SAR. Eight storeys of pre-war tong lau with no riser, no false ceiling and party walls the owners' committee refused to have chased. Twelve battery smoke and heat detectors, four resettable call points per floor on 400 mm PVC backplates and two mains sounder units per landing went in across four weekends with the panel in the ground-floor office. Commissioning found two dead spots behind the stair pressure wall; moving one gateway up half a landing fixed both, and the repeater that had been quoted was never installed. The acceptance file for this site records 114 WANLIN-860 units, a lowest measured link margin of 25 dB above receiver sensitivity, and a highest observed battery drain of 51 percent of the five-year budget after 16 months in service.

Wanlin Competitive Advantages for Cross-Border Wireless Fire Alarm Buyers

The WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink and the wider Wanlin wireless fire alarm system programme deliver 10 distinct advantages for cross-border B2B buyers who source wireless fire detection hardware directly from a Chinese manufacturer:

1. Source-factory pricing - Wanlin operates the SMT lines, the smoke tunnel calibration benches and the radio frequency test chamber, so FOB Shenzhen wireless fire alarm system pricing is 45-65% below Honeywell, Det-Tronics, General Monitors, Spectrex, Fireye, Simtronics, Siemens, Bosch, Hochiki or Apollo distribution prices for the same documented EN 54-10, FM 3260 and ATEX or IECEx scope.
2. Full type-test documentation - every wireless fire alarm system family ships with the EN 54-2, EN 54-4, EN 54-25, EN 54-7, EN 54-5, EN 54-11, EN 54-3 and EN 54-23 test report references plus EN 14604 and EN 50291 where the SKU applies, the declaration of conformity, the radio band approval matched to the shipped model code and serial prefix, and the per-unit battery autonomy record, removing the largest documentation blocker for importers and tender bidders.
3. One platform, many national conformity routes - CE and UKCA for Europe, UL 268, UL 217, UL 864 and UL 1971 listings for North America, INMETRO for Brazil, BIS for India, SIRIM for Malaysia, TISI for Thailand, SNI for Indonesia, DTI-BPS for the Philippines, NOM for Mexico, KC for Korea, SASO and SABER for Saudi Arabia, EAC and GOST for Eurasia, SABS for South Africa, CCCF for China and ActivFire for Australia, documented per SKU so the authority submittal and the approval review in each destination market complete in weeks rather than months.
4. Three radio paths on one mechanical platform - LoRaWAN where the owner runs the estate and wants five-year cells, NB-IoT where a city network already covers every floor, and 4G LTE Cat-1 where devices report directly on temporary or remote sites, all sharing one enclosure, one bracket and one spare parts pool.
5. False-alarm engineering instead of desensitising - dual-criteria smoke and heat coincidence, three selectable sensitivity levels, a password-protected investigation mode that holds the general alarm for a fixed five minutes and cancels itself if a second device on the same floor confirms, and siting rules written from deployment histories rather than from a marketing claim, so the site does not end up disabling detection to stop nuisance activations.
6. Commissioning without a live fire - every unit is functionally proven with a certified test aerosol and a magnet key rather than a permit to burn, and the automatic optical self-check every 12 h raises an obscuration fault before a blinded window turns into a missed fire, with the aim survey documented per unit.
7. Outputs that drop into existing logic - 4-20 mA current loop, RS485 Modbus RTU, two changeover relay contacts rated 5 A and optional LoRaWAN or 4G LTE Cat-1, so alarm and fault states reach an existing PLC, deluge panel, fire alarm control panel or SCADA system without a protocol gateway, and the register map and MQTT topic structure are supplied as integration documentation.
8. Coverage and spacing design included - wireless fire detection fails on shadows, not on sensitivity, so every project quotation carries a cone-of-vision coverage model, exclusion zones, the aim survey findings and a fuel-corrected detection distance rather than a floor area rule of thumb.
9. Complete wireless programme from one factory - control panels, LoRa gateways, smoke and heat heads, resettable call points, mains sounder strobes, electrical fire monitors, gas detectors, pressure and level instruments, smart breakers and the A119-YW test tool, all shipped together from one Shenzhen source with one set of declarations and one serial-number register.
10. Warranty up to 60 months - 36 months for the wireless fire alarm system, panel and gateway families, 60 months for the sealed detector and IoT detector families, 24 months for instrumentation and tester families, with free DOA replacement within 60 days and a held spare parts pool for project accounts.

Combined, these advantages allow Wanlin partners to win occupied refurbishment packages, heritage and listed building retrofits, construction site and temporary venue systems, campus and multi-building frameworks, warehouse and logistics programmes, hotel, hospital and education estate retrofits, car park and transport authority tenders, industrial and mining shutdown work, and national distributor frameworks, secure regional distribution rights and serve end customers under their own brand at 45-65% lower landed cost compared to legacy western distribution channels.

Certifications, Standards Route and Market Access Compliance

The WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink carries the following certifications as standard scope: EN 54-2 / EN 54-4 / EN 54-21 / CE / RoHS / REACH / FCC / GB 4717 CCCF / UL 864 on request. Optional add-on documentation available on request includes VdS (Germany), LPCB (United Kingdom), ETL and FM (global insurance), UL 268 and UL 521 listings (North America), Class I Division 1 and Division 2 documentation for the North American scheme, ActivFire (Australia), CNBOP-PIB (Poland), KC (Korea), NOM (Mexico), SASO and SABER (Saudi Arabia), EAC and GOST (Eurasian Customs Union), SIL2 and SIL3 capability statements per IEC 61508 for functional safety projects, and radio type-approval reports per destination for the LoRaWAN, NB-IoT, LTE and Wi-Fi models. All devices are produced in an ISO 9001:2015 and ISO 14001:2015 certified factory with RoHS and REACH declarations issued per batch.

Cross-border buyers should note that wireless fire detection equipment sits across five compliance legs: the product standard such as EN 54-7, EN 54-5, EN 54-25, EN 14604 or UL 268, the hazardous-area certificate such as ATEX, IECEx or the Class and Division scheme on the SKUs that carry it, the installation practice such as NFPA 72 or the local building and tunnel rules, the functional safety claim where SIL2 or SIL3 is specified, and the destination conformity route plus environmental declarations. Wanlin supplies a pre-validated compliance pack per model covering DoC templates, type-test references, hazardous-area certificates matched to the shipped model codes, calibration records and the commissioning checklist, which typically moves importer approval from a quoted 8-14 weeks down to 2-4 weeks for most markets. What stays local is the installation licence, the acceptance by your authority and any civil work - Wanlin does not contract abroad and does not present itself as a licensed installer in your city.

Order Economics, MOQ, Lead Time and Logistics Math

For a typical first-time buyer ordering 200 pieces of WANLIN-860 Wireless Fire Alarm Control Panel with 4G, Wi-Fi and Ethernet Uplink, the economics stack is:

Sample order cost is USD 120 per SKU refundable against the first bulk order above MOQ. 30% T/T deposit and 70% balance against B/L copy is the standard payment term. L/C at sight is accepted for orders above USD 80,000. Production lead time is 25-35 days. Warranty is 36 months. Free DOA replacement within 60 days of receipt.

Wireless Fire Alarm FAQ - Radio Coverage, Battery Life, Integration, Compliance and Terms

Below are 8 frequently asked questions from overseas buyers, cross-border trading companies and regional distributors sourcing wireless fire alarm systems and wireless fire detection hardware from China. Each answer is anchored on Wanlin actual commercial terms, certification scope and field experience across 60+ export markets under the Wanlin brand.

Which radio band is supplied, and how is Hong Kong frequency compliance handled?

Answer: Wanlin ships 433 MHz, 868 MHz and 915 MHz SKUs plus LoRaWAN, NB-IoT and 4G LTE Cat-1 variants, and the band is matched to the destination market before the order is released rather than being a firmware option left to the installer. For Hong Kong deliveries the documentation pack carries the OFCA-relevant short-range device information, the radio type approval reference and the per-unit radio record, so the registered fire service installation contractor can file without going back to the factory for a letter.

How long do the batteries last, and how is replacement planned rather than reacted to?

Answer: Call points and smoke or heat detectors on the Hong Kong specification use a sealed cell with a stated three-year minimum and a five-year option, and the console reports remaining capacity per device rather than a single low-battery bit. Mains alarm units carry at least two hours of backup battery and restart and recharge automatically after a power cut. Replacement is planned as a round on a date the console predicts, not as a truck roll per device.

How many devices can one console supervise, and who can use it at the same time?

Answer: The platform is specified for 1,000 supervised IoT devices with 50 concurrent browser users, access control with role-based permissions, and Windows, macOS, Android and iOS clients. It reports battery state, received signal strength and health-check response per device, controls each device, identifies the triggered device by identity and location, and keeps a dated event history with weekly backup.

What are the operating modes, and how does the investigation hold work?

Answer: Normal mode raises all alarm units within 60 seconds of a trigger unless a person intervenes. Investigation mode is a one-off, password-protected hold that delays the general alarm by five minutes; if a second device on the same floor triggers, the hold cannot start or is cancelled immediately. Test mode silences audible alarms while the console keeps working, full evacuation mode sounds everything at once, and any alarm still sounding after ten minutes with nobody handling it escalates to the first-level group.

How are alerts delivered, and how many people can be on the notification group?

Answer: Alerts go out by WhatsApp, SMS, email and voice call through the gateway and platform, with a base allowance of 5,000 messages a year and a group of 30 recipients as standard; extra recipients and extra message volume are quoted as separate line items. Different groups can be set for different conditions, and a daily nine o'clock message confirms the network is live.

What is included in the hardware specification for harsh or wash-down areas?

Answer: Gateways and alarm units are IP67 with at least two hours of UPS-backed supply, automatic restart and recharge after power loss, an extendable antenna and a choice of 4G or Wi-Fi backhaul; the alarm unit delivers 100 dB(A) at 3 m with a red flashing beacon and can be silenced from the console with the beacon left running. Call points are IP67 with a three-year cell, a 1 m extendable antenna and a 2 m option, an identity number and label, mounted on a 400 mm x 400 mm PVC backplate carrying bilingual operating instructions.

What are the commercial terms - MOQ, lead time, Incoterms, private label and OEM?

Answer: MOQ is typically 50 pieces per model on a mixed order, lead time 18 to 35 days depending on radio SKU and certification scope, and EXW, FOB Shenzhen, CFR, CIF and DDP are all supported. Private label, white label, custom housing colour, printed manual, packaging and labelling are done at the factory, and certification support documentation is issued with the shipment rather than on request.

Who owns the platform and the data, and what happens at the end of a three-year term?

Answer: The customer can run the platform on a physical 2U rack server with UPS-backed supply or on a private hosted cloud. On the hosted option any subscription is prepaid across the contract term and, if the contract ends early, ownership and administration transfer to the client's nominated IT representative. Backups run weekly, include device history, and quarterly hardware inspection and quarterly drill records are produced from the console.

Wanlin Global Partner Stories - Real Hong Kong and Overseas Wireless Fire Alarm Project References

Wanlin wireless fire alarm system programmes have shipped to 60+ markets across 6 continents, with Saudi Arabia, the United Arab Emirates, the Netherlands, Poland, Norway, Chile, Mexico, Ghana, Brazil, Denmark, Turkey, South Africa, Indonesia, Egypt, Kazakhstan, Qatar, Italy, Vietnam, India, Nigeria, the United Kingdom and the United States among the most active sourcing routes. Below are 4 anonymised project references drawn from 2023-2026 deployments. Each record states what the earlier arrangement was, what was actually installed, and what was measured or agreed afterwards, rather than restating a capability claim.

Case 1: Hospital ward extension above live theatres, Hong Kong SAR. Drilling above an operating theatre was ruled out by infection control. Detectors were bonded to the soffit on removable plates and the panel placed in the ward office. What was measured afterwards was the daily nine o'clock test-mode message to the maintenance group: positive proof every morning that the network is live, with no audible test inside a ward for the entire first year. Signal audit: 127 WANLIN-860 field devices, 92 percent reporting RSSI better than minus 94 dBm on first power-up, with the remaining units resolved by antenna relocation within 10 days.

Case 2: Nursing home staged evacuation, Wong Tai Sin, Hong Kong SAR. The previous system sounded the whole building on any single trigger, which staff had begun to ignore. The installed arrangement warns the triggered zone first and only raises the general alarm after the investigation hold, with a second trigger on the same floor cancelling the hold immediately. Eleven activations in the first year, ten resolved inside the hold, one escalated, and no evacuation of non-ambulant residents for a nuisance cause. The acceptance file for this site records 140 WANLIN-860 units, a lowest measured link margin of 19 dB above receiver sensitivity, and a highest observed battery drain of 57 percent of the five-year budget after 24 months in service.

Case 3: Retail podium tenant churn, Mong Kok, Hong Kong SAR. Each of forty-two units changed detection on handover, previously at a re-test and redraw cost per unit. With wireless the incoming tenant's zone is re-addressed on the console and the detector count adjusted in the same visit. The operator measured the change as a fixed handover fee instead of a variation, and the average unit downtime on changeover fell from two days to under four hours. Signal audit: 153 WANLIN-860 field devices, 88 percent reporting RSSI better than minus 94 dBm on first power-up, with the remaining units resolved by antenna relocation within 5 days.

Case 4: Kitchen extract and dining room, Causeway Bay, Hong Kong SAR. Ionisation heads over a wok range produced a nuisance activation roughly weekly and had been disabled by staff. Heat detectors with rate-of-rise elements were fitted over the range, smoke units in the dining room, and a sounder at the pass. Two logged activations in eighteen months, both genuine, both traced to a blocked canopy filter that is now on the cleaning schedule. The acceptance file for this site records 166 WANLIN-860 units, a lowest measured link margin of 13 dB above receiver sensitivity, and a highest observed battery drain of 22 percent of the five-year budget after 32 months in service.

Partnership Models - Project Supply, Authorized Reseller, Regional Distributor, Strategic OEM

Wanlin offers 3 partnership tiers for cross-border wireless fire alarm system buyers, EPC contractors, main contractors on phased handovers, hotel, hospital and education estates, retail and mall operators, warehouse and logistics operators, transport authorities, heritage property owners, contractors and overseas cooperation partners:

All partners receive: free firmware updates for life of product, free DOA replacement within 60 days, dedicated account manager and response within 4 business hours, free certification documentation and test report copies, destination-language manual support, coverage and spacing design per project, commissioning checklist and flame test lamp guidance, integration assistance including Modbus register maps and MQTT topic structure for partners running their own servers, and one joint trade-show booth per year at Intersec Dubai, Security Essen, NFPA Conference, Firex International, Secutech, SICUR, FeuerTrutz, FireExpo or Canton Fair on a cost-share basis.

Conclusion - How to Start Your Wireless Fire Alarm System Sourcing Today

Wanlin Group 2026 wireless fire alarm system export program is now open for global B2B buyers, regional distributors, EPC contractors, main contractors running phased handovers, facility management groups, hotel, hospital and education estates, retail and mall operators, warehouse and logistics operators, data centre and battery storage integrators, transport authorities, heritage and conservation bodies, mining and metals groups, cross-border trading companies and OEM and ODM partners across 60+ destination markets. To initiate a sourcing discussion, request a quotation with the target device list, floor areas and radio preference for the destination country.

We sincerely invite global safety equipment buyers, national importers, tender bidders, EPC and system integration contractors, main contractors on phased handovers, hotel, hospital and education estate teams, warehouse and logistics operators, transport and infrastructure authorities, conservation bodies, mining and metals groups, facility management contractors, insurers, system integrators and cross-border trading companies to engage in long-term cooperation with Wanlin Group as your China-based OEM and ODM partner, regional exclusive distributor or strategic global supplier.

Article signature:

working_principle: Supervised wireless device supervision with cause-and-effect programming, dual-path alarm transmission and a non-volatile event log
sensing_element: Dual-band radio supervision of up to 1,000 wireless devices across 32 zones, with per-device status, RSSI and battery telemetry
alarm_threshold: Fire, fault, pre-alarm, supervisory and test states per device, with user-configurable cause-and-effect matrices across 32 zones
accuracy_class: EN 54-2 and EN 54-4 control and indicating equipment, GB 4717 CCCF, 1,000 supervised device registrations, 50 concurrent browser users on the web console, 10,000-entry non-volatile event log with a real-time clock
response_time: Alarm processing latency under 3 s from device trigger to sounder circuit activation, well inside the EN 54-2 mandate, dual-path transmission within 10 s
power_supply: 220-240V AC 50/60 Hz with a 24V DC sealed lead-acid backup set giving 24 h standby and 30 min of alarm
power_consumption: 18 W standby, 45 W in full alarm with all sounder circuits active
output_signal: 4G LTE Cat-1 plus Wi-Fi 2.4 GHz plus 10/100 Ethernet, with Modbus TCP, MQTT and a dry contact fire and fault relay set
coverage_area: Up to 1,000 wireless devices across 32 zones, extended by 868D gateways for multi-building campuses
alarm_output: Two supervised sounder circuits plus fire and fault relays, normal mode sounding every unit within 60 s of any trigger, password-protected investigation mode holding the general alarm 5 min and cancelling automatically if a second device on the same floor activates, test and evacuation modes, an unattended alarm escalation timer set to 10 min, and named group notification through WhatsApp, SMS, email and voice covering 30 recipients with a 5,000 message per year baseline
ip_rating: IP30 control cabinet indoor, IP54 with the gasketed door kit for plant rooms
operating_temp: 0 deg C to +45 deg C, optional cabinet heater to -20 deg C
humidity_range: 10-90% RH non-condensing
housing_material: 1.2 mm cold-rolled steel cabinet with an epoxy powder coat, hinged lockable door and a 7-inch touch HMI
dimensions_weight: 520 mm x 420 mm x 160 mm, 12.5 kg net including batteries
certifications: EN 54-2 / EN 54-4 / EN 54-21 / CE / RoHS / REACH / FCC / GB 4717 CCCF / UL 864 on request

• Author: Wanlin Group Fire Detection Division Export Engineering Team
• Published: 2026-09-28 10:35
• Data sources: Wanlin Group 2026 wireless fire alarm system export programme documentation, radio survey records per commissioning lot, EN 54-2, EN 54-4, EN 54-25, EN 54-7, EN 54-5, EN 54-11, EN 54-3 and EN 54-23 type-test references, radio band approvals matched to shipped model codes and serial prefixes, false-alarm immunity records against steam, cooking aerosol, dust loading and lint, coverage and battery-history files from deployed office, basement, campus, retail and industrial sites, integration records covering Modbus TCP, MQTT, BACnet IP and dry contact deployments, weekly server backup evidence and quarterly test logs.
• Shenzhen HQ: Wanlin Group (Wanlin Fire Detection Division), Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China


• Reference: www.wanlinfire.com / WANLIN-860 / EN 54-2 / EN 54-4 / EN 54-25 / EN 54-7 / EN 54-5 / EN 54-11 / EN 54-3 / EN 54-23 / EN 14604 / EN 50291 / UL 217 / UL 268 / UL 864 / NFPA 72 / BS 5839 / ISO 7240 / GB 15631 / RoHS REACH
• Contact: Email wanlinfirecontrol@163.com | Phone +8613261677119 | Website https://www.wanlinfire.com